Not to be used as substitute for the full, written specification
Test Method ISO
- Kinematic viscosity at 40 °C mm²/s max
6,000
3104
- Kinematic viscosity at 40 °C mm²/s min
2,000
3104
- Density at 15°C kg/m³ max
890,0
3675 or 12185
- CCAI max
-
Cetane index min
40
4264
- Sulphur mass % max
1,50
8754 14596
- Flash point °C min
60,0
2719
- Hydrogen sulfide mg/kg max
2,00
IP 570
- Acid number mg KOH/g max
0,5
ASTM D664
- Total sediment aged mass % max
-
10370-2
- Total sediment by hot filtration mass % max
-
10307-1
- Oxidation stability g/m³ max
25
12205
- Carbon residue; micro method mass % max
-
10370
- Carbon residue; micro method on the 10% volume distillation residue mass % max
0,30
10370
- Cloud point °C max
-
3015
- Pour point (upper) Winter quality °C max
-6
3016
- Pour point (upper) Summer quality °C max
0
3016
- Appearance
Clear and bright
- Water volume % max
-
3733
- Ash mass % max
0,010
6245
- Vanadium mg/kg max
-
IP504, IP470 or ISO 14597
- Sodium mg/kg max
-
IP501 IP470
- Aluminium plus silicon mg/kg max
-
IP501 or IP470 IP500
- Lubricity, corrected wear scar diameter (wsd 1, at 60°C μm max
520
12156-1
- Used Lubrication oils (ULO): Calcium and zinc; or calcium and phosphorus mg/kg
-
IP501 or IP470 IP500
Not to be used as substitute for the full, written specification
Test Method ISO
- Kinematic viscosity at 40 °C mm²/s max
11,00
3104
- Kinematic viscosity at 40 °C mm²/s min
2,000
3104
- Density at 15°C kg/m³ max
900,0
3675 or 12185
- CCAI max
-
Cetane index min
35
4264
- Sulphur mass % max
2,00
8754 14596
- Flash point °C min
60
2719
- Hydrogen sulfide mg/kg max
2,00
IP 570
- Acid number mg KOH/g max
0,5
ASTM D664
- Total sediment aged mass % max
-
10370-2
- Total sediment by hot filtration mass % max
0,10
10307-1
- Oxidation stability g/m³ max
25
12205
- Carbon residue; micro method mass % max
0,30
10370
- Carbon residue; micro method on the 10% volume distillation residue mass % max
-
10370
- Cloud point °C max
-
3015
- Pour point (upper) Winter quality °C max
0
3016
- Pour point (upper) Summer quality °C max
6
3016
- Appearance
-
- Water volume % max
0,30
3733
- Ash mass % max
0,010
6245
- Vanadium mg/kg max
-
IP504, IP470 or ISO 14597
- Sodium mg/kg max
-
IP501 IP470
- Aluminium plus silicon mg/kg max
-
IP501 or IP470 IP500
- Lubricity, corrected wear scar diameter (wsd 1, at 60°C μm max
520
12156-1
- Used Lubrication oils (ULO): Calcium and zinc; or calcium and phosphorus mg/kg
-
IP501 or IP470 IP500
Not to be used as substitute for the full, written specification
Test Method ISO
- Kinematic viscosity at 50 °C mm²/s max
10,00
3104
- Kinematic viscosity at 50 °C mm²/s min
-
3104
- Density at 15°C kg/m³ max
920,0
3675 or 12185
- CCAI max
850
Cetane index min
-
4264
- Sulphur mass % max
Statutory requirements
8754 14596
- Flash point °C min
60,0
2719
- Hydrogen sulfide mg/kg max
2,00
IP 570
- Acid number mg KOH/g max
2,5
ASTM D664
- Total sediment aged mass % max
0,10
10370-2
- Total sediment by hot filtration mass % max
-
10307-1
- Oxidation stability g/m³ max
-
12205
- Carbon residue; micro method mass % max
2,50
10370
- Carbon residue; micro method on the 10% volume distillation residue mass % max
-
10370
- Cloud point °C max
-
3015
- Pour point (upper) Winter quality °C max
0
3016
- Pour point (upper) Summer quality °C max
6
3016
- Appearance
-
- Water volume % max
0,30
3733
- Ash mass % max
0,040
6245
- Vanadium mg/kg max
50
IP504, IP470 or ISO 14597
- Sodium mg/kg max
50
IP501 IP470
- Aluminium plus silicon mg/kg max
25
IP501 or IP470 IP500
- Lubricity, corrected wear scar diameter (wsd 1, at 60°C μm max
-
12156-1
- Used Lubrication oils (ULO): Calcium and zinc; or calcium and phosphorus mg/kg
The fuel shall be free from ULO. A fuel shall be considered to contain ULO when either one of the following conditions is met: calcium > 30 and zinc > 15; or calcium >30 and phosphorus > 15
IP501 or IP470 IP500
Not to be used as substitute for the full, written specification
Test Method ISO
- Kinematic viscosity at 50 °C mm²/s max
30,00
3104
- Kinematic viscosity at 50 °C mm²/s min
-
3104
- Density at 15°C kg/m³ max
960,0
3675 or 12185
- CCAI max
860
Cetane index min
-
4264
- Sulphur mass % max
Statutory requirements
8754 14596
- Flash point °C min
60,0
2719
- Hydrogen sulfide mg/kg max
2,00
IP 570
- Acid number mg KOH/g max
2,5
ASTM D664
- Total sediment aged mass % max
0,10
10370-2
- Total sediment by hot filtration mass % max
-
10307-1
- Oxidation stability g/m³ max
-
12205
- Carbon residue; micro method mass % max
10,00
10370
- Carbon residue; micro method on the 10% volume distillation residue mass % max
-
10370
- Cloud point °C max
-
3015
- Pour point (upper) Winter quality °C max
0
3016
- Pour point (upper) Summer quality °C max
6
3016
- Appearance
-
- Water volume % max
0,50
3733
- Ash mass % max
0,070
6245
- Vanadium mg/kg max
150
IP504, IP470 or ISO 14597
- Sodium mg/kg max
100
IP501 IP470
- Aluminium plus silicon mg/kg max
40
IP501 or IP470 IP500
- Lubricity, corrected wear scar diameter (wsd 1, at 60°C μm max
-
12156-1
- Used Lubrication oils (ULO): Calcium and zinc; or calcium and phosphorus mg/kg
The fuel shall be free from ULO. A fuel shall be considered to contain ULO when either one of the following conditions is met: calcium > 30 and zinc > 15; or calcium >30 and phosphorus > 15
IP501 or IP470 IP500
Not to be used as substitute for the full, written specification
Test Method ISO
- Kinematic viscosity at 50 °C mm²/s max
80,00
3104
- Kinematic viscosity at 50 °C mm²/s min
-
3104
- Density at 15°C kg/m³ max
975,0
3675 or 12185
- CCAI max
860
Cetane index min
-
4264
- Sulphur mass % max
Statutory requirements
8754 14596
- Flash point °C min
60
2719
- Hydrogen sulfide mg/kg max
2,00
IP 570
- Acid number mg KOH/g max
2,5
ASTM D664
- Total sediment aged mass % max
0,10
10370-2
- Total sediment by hot filtration mass % max
-
10307-1
- Oxidation stability g/m³ max
-
12205
- Carbon residue; micro method mass % max
14,00
10370
- Carbon residue; micro method on the 10% volume distillation residue mass % max
-
10370
- Cloud point °C max
-
3015
- Pour point (upper) Winter quality °C max
30
3016
- Pour point (upper) Summer quality °C max
30
3016
- Appearance
-
- Water volume % max
0,50
3733
- Ash mass % max
0,070
6245
- Vanadium mg/kg max
150
IP504, IP470 or ISO 14597
- Sodium mg/kg max
100
IP501 IP470
- Aluminium plus silicon mg/kg max
40
IP501 or IP470 IP500
- Lubricity, corrected wear scar diameter (wsd 1, at 60°C μm max
-
12156-1
- Used Lubrication oils (ULO): Calcium and zinc; or calcium and phosphorus mg/kg
The fuel shall be free from ULO. A fuel shall be considered to contain ULO when either one of the following conditions is met: calcium > 30 and zinc > 15; or calcium >30 and phosphorus > 15
IP501 or IP470 IP500
Not to be used as substitute for the full, written specification
Test Method ISO
- Kinematic viscosity at 50 °C mm²/s max
180,0
3104
- Kinematic viscosity at 50 °C mm²/s min
-
3104
- Density at 15°C kg/m³ max
991,0
3675 or 12185
- CCAI max
860
Cetane index min
-
4264
- Sulphur mass % max
Statutory requirements
8754 14596
- Flash point °C min
60,0
2719
- Hydrogen sulfide mg/kg max
2,00
IP 570
- Acid number mg KOH/g max
2,5
ASTM D664
- Total sediment aged mass % max
0,10
10370-2
- Total sediment by hot filtration mass % max
-
10307-1
- Oxidation stability g/m³ max
-
12205
- Carbon residue; micro method mass % max
15,00
10370
- Carbon residue; micro method on the 10% volume distillation residue mass % max
-
10370
- Cloud point °C max
-
3015
- Pour point (upper) Winter quality °C max
30
3016
- Pour point (upper) Summer quality °C max
30
3016
- Appearance
-
- Water volume % max
0,50
3733
- Ash mass % max
0,070
6245
- Vanadium mg/kg max
150
IP504, IP470 or ISO 14597
- Sodium mg/kg max
50
IP501 IP470
- Aluminium plus silicon mg/kg max
50
IP501 or IP470 IP500
- Lubricity, corrected wear scar diameter (wsd 1, at 60°C μm max
-
12156-1
- Used Lubrication oils (ULO): Calcium and zinc; or calcium and phosphorus mg/kg
The fuel shall be free from ULO. A fuel shall be considered to contain ULO when either one of the following conditions is met: calcium > 30 and zinc > 15; or calcium >30 and phosphorus > 15
IP501 or IP470 IP500
Not to be used as substitute for the full, written specification
Test Method ISO
- Kinematic viscosity at 50 °C mm²/s max
180,0
3104
- Kinematic viscosity at 50 °C mm²/s min
-
3104
- Density at 15°C kg/m³ max
991,0
3675 or 12185
- CCAI max
870
Cetane index min
-
4264
- Sulphur mass % max
Statutory requirements
8754 14596
- Flash point °C min
60
2719
- Hydrogen sulfide mg/kg max
2,00
IP 570
- Acid number mg KOH/g max
2,5
ASTM D664
- Total sediment aged mass % max
0,10
10370-2
- Total sediment by hot filtration mass % max
-
10307-1
- Oxidation stability g/m³ max
-
12205
- Carbon residue; micro method mass % max
18,00
10370
- Carbon residue; micro method on the 10% volume distillation residue mass % max
-
10370
- Cloud point °C max
-
3015
- Pour point (upper) Winter quality °C max
30
3016
- Pour point (upper) Summer quality °C max
30
3016
- Appearance
-
- Water volume % max
0,50
3733
- Ash mass % max
0,100
6245
- Vanadium mg/kg max
350
IP504, IP470 or ISO 14597
- Sodium mg/kg max
100
IP501 IP470
- Aluminium plus silicon mg/kg max
60
IP501 or IP470 IP500
- Lubricity, corrected wear scar diameter (wsd 1, at 60°C μm max
-
12156-1
- Used Lubrication oils (ULO): Calcium and zinc; or calcium and phosphorus mg/kg
The fuel shall be free from ULO. A fuel shall be considered to contain ULO when either one of the following conditions is met: calcium > 30 and zinc > 15; or calcium >30 and phosphorus > 15
IP501 or IP470 IP500
Not to be used as substitute for the full, written specification
Test Method ISO
- Kinematic viscosity at 50 °C mm²/s max
380,0
3104
- Kinematic viscosity at 50 °C mm²/s min
-
3104
- Density at 15°C kg/m³ max
991,0
3675 or 12185
- CCAI max
870
Cetane index min
-
4264
- Sulphur mass % max
Statutory requirements
8754 14596
- Flash point °C min
60,0
2719
- Hydrogen sulfide mg/kg max
2,00
IP 570
- Acid number mg KOH/g max
2,5
ASTM D664
- Total sediment aged mass % max
0,10
10370-2
- Total sediment by hot filtration mass % max
-
10307-1
- Oxidation stability g/m³ max
-
12205
- Carbon residue; micro method mass % max
18,00
10370
- Carbon residue; micro method on the 10% volume distillation residue mass % max
-
10370
- Cloud point °C max
-
3015
- Pour point (upper) Winter quality °C max
30
3016
- Pour point (upper) Summer quality °C max
30
3016
- Appearance
-
- Water volume % max
0,50
3733
- Ash mass % max
0,100
6245
- Vanadium mg/kg max
350
IP504, IP470 or ISO 14597
- Sodium mg/kg max
100
IP501 IP470
- Aluminium plus silicon mg/kg max
60
IP501 or IP470 IP500
- Lubricity, corrected wear scar diameter (wsd 1, at 60°C μm max
-
12156-1
- Used Lubrication oils (ULO): Calcium and zinc; or calcium and phosphorus mg/kg
The fuel shall be free from ULO. A fuel shall be considered to contain ULO when either one of the following conditions is met: calcium > 30 and zinc > 15; or calcium >30 and phosphorus > 15
IP501 or IP470 IP500
Not to be used as substitute for the full, written specification
Test Method ISO
- Kinematic viscosity at 50 °C mm²/s max
500,00
3104
- Kinematic viscosity at 50 °C mm²/s min
-
3104
- Density at 15°C kg/m³ max
1010,0
3675 or 12185
- CCAI max
870
Cetane index min
-
4264
- Sulphur mass % max
Statutory requirements
8754 14596
- Flash point °C min
60
2719
- Hydrogen sulfide mg/kg max
2,00
IP 570
- Acid number mg KOH/g max
2,5
ASTM D664
- Total sediment aged mass % max
0,10
10370-2
- Total sediment by hot filtration mass % max
-
10307-1
- Oxidation stability g/m³ max
-
12205
- Carbon residue; micro method mass % max
20,00
10370
- Carbon residue; micro method on the 10% volume distillation residue mass % max
-
10370
- Cloud point °C max
-
3015
- Pour point (upper) Winter quality °C max
30
3016
- Pour point (upper) Summer quality °C max
30
3016
- Appearance
-
- Water volume % max
0,50
3733
- Ash mass % max
0,150
6245
- Vanadium mg/kg max
450
IP504, IP470 or ISO 14597
- Sodium mg/kg max
100
IP501 IP470
- Aluminium plus silicon mg/kg max
60
IP501 or IP470 IP500
- Lubricity, corrected wear scar diameter (wsd 1, at 60°C μm max
-
12156-1
- Used Lubrication oils (ULO): Calcium and zinc; or calcium and phosphorus mg/kg
The fuel shall be free from ULO. A fuel shall be considered to contain ULO when either one of the following conditions is met: calcium > 30 and zinc > 15; or calcium >30 and phosphorus > 15
IP501 or IP470 IP500
Not to be used as substitute for the full, written specification
Test Method ISO
- Kinematic viscosity at 50 °C mm²/s max
700,0
3104
- Kinematic viscosity at 50 °C mm²/s min
-
3104
- Density at 15°C kg/m³ max
1010,0
3675 or 12185
- CCAI max
870
Cetane index min
-
4264
- Sulphur mass % max
Statutory requirements
8754 14596
- Flash point °C min
60,0
2719
- Hydrogen sulfide mg/kg max
2,00
IP 570
- Acid number mg KOH/g max
2,5
ASTM D664
- Total sediment aged mass % max
0,10
10370-2
- Total sediment by hot filtration mass % max
-
10307-1
- Oxidation stability g/m³ max
-
12205
- Carbon residue; micro method mass % max
20,00
10370
- Carbon residue; micro method on the 10% volume distillation residue mass % max
-
10370
- Cloud point °C max
-
3015
- Pour point (upper) Winter quality °C max
30
3016
- Pour point (upper) Summer quality °C max
30
3016
- Appearance
-
- Water volume % max
0,50
3733
- Ash mass % max
0,150
6245
- Vanadium mg/kg max
450
IP504, IP470 or ISO 14597
- Sodium mg/kg max
100
IP501 IP470
- Aluminium plus silicon mg/kg max
60
IP501 or IP470 IP500
- Lubricity, corrected wear scar diameter (wsd 1, at 60°C μm max
-
12156-1
- Used Lubrication oils (ULO): Calcium and zinc; or calcium and phosphorus mg/kg
The fuel shall be free from ULO. A fuel shall be considered to contain ULO when either one of the following conditions is met: calcium > 30 and zinc > 15; or calcium >30 and phosphorus > 15
IP501 or IP470 IP500
Friedrich G. Frommann GmbH & Co. KG ,Winsener Stieg 6, 21079 Hamburg, Tel.: 0 40 / 76 62 68 - 0, info@frommann.info